Tag: building

Everything, Including the Kitchen Sink

Published on by Our Humble Abode20 Comments

Wednesday afternoon we finished installing the new 3/4 inch thick stained hickory floor.  And we’re completely in love.

With the floor done, we started installing the cabinets Thursday morning.  Because we’re washing dishes in the bathroom sink, getting a sink was a pressing matter.  Rather than incorporating the toe kick in the cabinet, we cheat and build separate toe kicks.  Two by fours are the perfect height and they’re durable, so Ben makes boxes three inches smaller than the overall cabinet size.

Using long screws, Ben attached the boxes to the floor.

That part went quickly.

For the next several hours, Ben drilled several holes in our floor and ran tons of wires.

Wires for what?  Ben’s awesome idea.  Under cabinet lighting.  And not the halogen task lighting.  Rope lighting under the toe kicks.  A similar idea to the crown molding accent lighting in our master bedroom.  We’ve had several people ask how to do this.  I’m no electrician, so don’t quote me here, but Ben starts with a piece of rope light with a plug-in end.  He cuts the plug off and strips the wires.  Then it’s just a matter of connecting the proper wires to one another and capping everything off with wire nuts and electrical tape.

The posts we have on each side of the stove are mostly for support.  In an effort to keep the posts as small and unobtrusive as possible, we decided to put our switches inside the cabinets on the living room side.  We’ll have a bar top across the cabinets with a six-foot opening between for bar stools.  Here’s one of the cabinets by the kitchen entrance.

Don’t follow?  Here’s what it looks like from the kitchen side.

While Ben ran wires, Everett and I cheered him on.  Every time Ben nailed or screwed something down, Ev would say, “Nice!”

 

Ben took the afternoon off to go hunting.  Fortunately, he shot a deer, so he’s done for the rest of the year.  Unfortunately, we still didn’t have a kitchen sink.  Which means he had to clean his deer in our bathroom.  To say I was displeased is an understatement.  We needed a functioning sink, stat.  Friday morning Ben started working again, setting cabinets.

A small kitchen requires maximizing every square inch.  Even though we’re losing an entire wall of upper cabinets, we’re gaining a lot of usable space.  In fact, the only wasted space is this three-inch gap between the peninsula and trash drawer.  The only reason for this is drawer clearance.

Shortly before the sink could be installed, Ben brought it up from the basement.

 

A little more wiring for the dishwasher, which we ordered and should be here on Thursday, before the sink could go in.

Then some plumbing.

After five days without a kitchen sink, we were back in dish washing business.

Then we had a little leak.  Everything worked, but the leak came from dishwasher hook up.  Because we don’t have a dishwasher.

Duct tape over the hole works for now.  And here’s the sink side in its current state.  Oh, you’ll also see we have the trash under the sink.  After buying a 10.1 gallon trash and putting it in the trash drawer we realized there would be a fair amount of wasted space above it.  Luckily, it fits perfectly under the sink.  Along with another can for recycling.  Which means, we’re gaining a small drawer stack in the place of the original trash drawer.

In other news, we hoped the wood for the counters would arrive this past Thursday.  Sadly, it didn’t.  Now we’re shooting for Wednesday.  Fingers crossed it comes in and we like it so we can get counters in.  Though, we’re lucky because Ben built the cabinets with flat tops, so we have a solid work surface.  Things could definitely be worse.

Many of you commented that we’re making quick progress.  Even though we’re living with a torn apart kitchen, I have to agree.  Everything is back to functioning order and it can only get better from here.

What do you think of the kitchen so far?  Progressing faster than you anticipated?  Just wait until you see tomorrow’s post.  Yes, that is a teaser.

Ventilation

Published on by Our Humble Abode12 Comments

Everyone can use a little ventilation.  Unless you’re Lindsay Lohan or Paris Hilton and you’re getting out of a car with swarms of paparazzi watching every move you make.  Maybe I should say every kitchen should have adequate ventilation, especially over the range.  Just to pull the smells, heat, and moisture out.  It comes in really handy when you burn something, too.  Not that I’ve ever done that.  My point is, after tearing down the wall between the kitchen and living room on Saturday, Ben installed our new vent hood.  I briefly explained our vent hood choice in this post, but we’re sharing all the details now.

We started with a 40 inch insert, with plans to hang it as close to the ceiling as possible.  You know that nice hole we opened up?  Yeah, we didn’t want to cover any of it.

To get started, Ben found the center of the wall and marked it.  Of course, it came out on a joist.  Ben did some bracing in the attic and then proceeded to cut a hole in the sheet rock and joist to run the duct work.

Our vent hood, like most, had one flat side and three angled sides.  Typically, the flat side would be mounted against the wall and the remaining three sides could be boxed out either square or following the angles.

For about two seconds, we considered building a box that followed the angles of the fan, but we decided not to for two reasons.  Number one, we’re planning to add decorative trim and paint everything white and the angles would complicate that.  Number two, Ben worried (and I did too after he mentioned it) about grease and dust settling on the angle and we’d have a perma-dirty hood.  We opted for the simpler square box frame.  Ben carefully measured the vent and built a 2 by 4 box surround to support the new fan.  He screwed it into the joists to make sure it was securely held in place.

In goes the vent, held 1/2 inch from the bottom using the adjustable brackets that came with.  Smartie Ben used a piece of sheet rock as the guide for the spacing.  You’ll also notice that we put the flat part to the front.  This is because our vent has several buttons (for lights and various fan speeds) on the inside of the insert.  I’m short and this sucker (literally) is tucked right up to the ceiling.  If we had turned it 180 degrees, I wouldn’t be able to reach the buttons without either burning myself or getting a chair to stand on.  Neither of which seem ideal.

With everything wired up, Ben covered the box with sheet rock.  Now, our giant hole in the wall looks something like this.

In all honestly, I was a little shocked at how deep it was.  In the week since we took the cabinets and soffit down, I had gotten used to the open feel.  And I really liked how much more open everything was after knocking down the wall.  So this seemed heavier than I anticipated.  But, I was so happy the vent hood only drops 1/2 inch below the sheet rock of the support beam.

Not to mention getting task lighting and a fan back.

And it’s still pretty from the underside.

The 1200 CFM fan provides more than enough air circulation and it’s still quiet.  After installing, Ben turned it on the highest setting and we could still hear the music and carry on a normal conversation between the kitchen, living, and dining areas.  Two weeks ago, this is what you saw when you walked in the front door.

And now, behold our kitchen (and Vincent’s head) from the same angle.

It was difficult to get a good picture with all that new light streaming in from the dining room and sink windows.  Still more sheet rocking to do.  And, don’t pay attention to the too tall stove back, microwave, and jumble of wires.  If you’re concerned about safety, we’ve securely closed off the outlets so little fingers can’t get in.

Consider your self up to date on the kitchen progress.  Hopefully we’ll get some sconces, finish up some cabinet work, and look for countertops soon.  Of course we’ll keep you updated on any and all progress.  You’ve been warned.  Annoying minute details are in your future.

The boys and I are off to do some shopping.  Cross your fingers for a good deal!

And the Walls Come Tumblin’ Down

Published on by Our Humble Abode21 Comments

If you follow us on Facebook, you already know we tackled more demo work this weekend.  Quite literally.  Ben got pretty physical with it.  The destruction took place in the kitchen, to the wall standing between the living room.  The process was pretty straight forward.  First, Ben removed the baseboard, chair rail, and an old no longer in use vent.  Just to make sheet rock tearing easier.

Then, from the kitchen side, Ben kicked some sheet rock butt.  Meaning he actually kicked his foot through.  With the rock loose, he used his hands to tear out chunks.  Some small.

Some large.

Because this wall is load bearing, Ben has reinforced everything in the attic, but we’re also keeping a beam and support posts down below.  To try to minimize sheet rock repairs, we decided to try to save the sheet rock which will cover the future beam.  Ben had an idea that sounded like it would break the sheet rock cleanly, both from the lower rock and studs.  First, he measured the height of the beam and marked the wall.  Then, he screwed a scrap of wood and scored along the edge.  He left the board up while tearing the sheet rock off.

Luckily, it worked like a charm.  Now we hoped the studs would come off cleanly.

Using a hammer and brute strength, Ben knocked each stud out, first at the bottom, then at the top.  And, the sheet rock stayed nearly perfect.  Wahoo for not having to patch more drywall and install new crown.

Open sesame!!  It’s so much brighter.  Funny story.  Just after Ben tore the sheet rock off the wall, I had to put something in the entry closet.  I noticed a sliver of light and looked for something reflecting light.  Then, I realized, this was the first time I’d ever seen fresh light at that angle.  Such a happy moment.  I know, I’m a mega nerd.

Even better, we can finally see from the kitchen into the living room.  No more wondering why Everett is crying when he’s on the other side.  I can see him.  Oh, and you can see the recessed can lights Ben installed on Thursday night.  Yeah, that’s what I’m talking about.  We centered one over each work surface for direct task lighting.  We’ll also have lights in the vent hood over the range.

Genius Ben had another great lighting idea.  You could say a light bulb moment.  Ahah.  He wisely suggested we move the stove side lights closer to the beam, rather than centered over the counter.  Why?  So people on the couch wouldn’t be blinded by the light (name that band).  Once the decorative halos are in, the lights closer to the sink won’t be as visible either.

And here we are after a day of demo.  You’ll notice boxes for our sconces as well as our child safe light switch placement.  Of course that is temporary, but we’re moving stuff around so much lately.

Now for the best part.  Looking from the back door through the kitchen to the living room and beyond.  And, you can see the beam Ben installed along the top, which matches the dining room perfectly.

Yes, I did stop vacuuming to get Vincent a yogurt and take this picture.  Excuse the mess and the giant microwave that won’t stay.  We’re all so excited to finally see our plans come to life.  Vincent and Everett already love to sit on the chair near the stove to watch and beg for snacks.

That’s how we like to spend our Saturdays.  But we did a little more on Sunday, involving our vent hood.  What did you do?

P.S.  Manfred Mann.