Green = Green: Reclaimed Wood

Hey everyone!  Glad to see you here today.  Did you have a good weekend?  We’ve spent most of our last two (including Memorial Day) working on a back yard deck.  If you’re thinking, “Wait, I thought you were going to have a concrete patio back there?” you’d be right.

Back-Yard-Landscape-Plan-Sept-2012

That was the plan up until a few weeks ago, but our plans are kinda fluid.  If our original plan won’t work, we find a better project, or a kick butt deal, we’re willing to switch things up.  Heck, that’s how we ended up with wood countertops at our last house.

When Ben stumbled into the deal of the century, we couldn’t say no.  You see, a commercial building in town was in the process of being demolished.  Outside sat a giant stack of glulam beams, originally used to support the roof.

Back-Deck-Reclaimed-Beams

Ben called around until he found the guy responsible for these dudes and asked what the heck deal was.  Well, they were destined for landfill.  Landfill, not on our watch!  Instead Ben cut these giants down, hauled ’em home, and we’re building a deck now.  But they’re not deck ready in their original condition.

Deck-Beam-Before

Purple paint, screw and nail holes, and gouges from the not super concerned excavator operator need some attention.

Back-Deck-Mud-Pit

But, the mud pit we call a back yard is slowly becoming a user-friendly, dirt free space.  Here’s where we are today:

Back-Deck-Progress

Nineteen beams in place, seven to go.  Each beam is 5 1/4 inches thick, 19 1/4 inches wide, 15 or 16 feet long, and weighs about 300 pounds each.  In a word, massive.  Admittedly, I’m of little help moving these bad mamba jambas.  It’s quite comical, actually.  Ben summons his Hulk powers while I’m all Captain America, pre experimental serum.  However, I can fetch tools, pull nails, and help decide which side of each beam looks better.

Back-Deck-Reclaimed-Beam-Stack

The deck sits about six inches off the ground with a slight cantilever off the ends.

Back-Deck-Over-Hang

Before we can put each beam in place, we’ve got to pull out all nails and screws, sand off the paint, and smooth the grooves from the demo.  Damage from the removal gives each beam some rustic character.

Back-Deck-Character-of-Beams

Even though the sides have a some pitting, the tops are super smooth.  I’ve carefully and scientifically measured the tripping hazard of each side, not yet stubbed a toe or fallen.

Back-Deck-Character

Of course we’re still not done.  Seven more beams until we’re at the desired width.

Back-Deck-Toward-Stack

Then we’ll use a large sander (likely a rented one for hardwood floors) to go over the top, smoothing everything.  Oh, we’ll have the fun task of cutting all the ends to make a clean, straight edge, too.  Normal skill saws don’t even come close to cutting through.

Back-Deck-Uneven-Ends

We’ll seal the virgin wood with a mid-toned stain, for a little depth and color.  And we’ll have to build stairs to this little rock landing.  No more mudslides, thank you.

Back-Deck-Stairs-to-Make

Despite not being done, we’re already enjoying using the deck.  For waterfall sitting, of course.

Back-Deck-Toward-Waterfall

Once we’ve finished the deck, we’ll cover the rest of the muddy areas with plastic, crushed limestone, and add some plants.  Because we need greenery.  I’m thinking a shady little hosta/bleeding heart/lily of the valley bed outside of the bedroom windows.  And build a pergola.  And add a gas fire pit.  And cover the house in new siding.  Yes, we’ve got big plans for this summer.

What do you think of the newest addition?  We’re smitten with him so far.  Anyone else building a deck?  Or adding greenery to a yard?

MCM, Modernized

Hello and happy Monday, if there is such a thing.  On Friday I shared the blow-by-blow of my five dollar chair refinishing and upholstering process.  Starting with these 70’s dark stained orange vinyl covered wood beauties.

ReStore-Chairs-by-Fireplace-Before

And here they are now, after an overall sanding, clear coat, thick neutral fabric, and satin nickel nail head detail.

MCM Chairs Finished in Family Room

Once I started sanding the wood down, I saw how blonde the wood was.  And liked it.  A lot, for a few reasons.  Lighter felt more updated, less reminiscent of the Brady Bunch kitchen color palette.  The pale wood also contrasted with the dark slate fireplace, instead of blending in.  After going through the trouble to sand to the unfinished wood, I didn’t want a dark stain that wouldn’t be an obvious change.  Also, I’m leaning toward natural finished wood, for a little variety.

MCM Chairs Finished Right

Even though the chairs are neutral, I’m super happy with the go anywhere colors and subtle patterned fabric.

MCM Chairs Finished Left

To bump up the comfort and color, I plan to find or sew lumbar pillows.

MCM Chairs by Fireplace from Breakfast Nook

That  little footstool will get an update and jolt of color sometime soon, too.  Because paint is easier and cheaper to change than upholstery and stain.  These chairs work great in the family room.  Comfy, but light weight and open.  Can’t forget the price, either.  Only $32 spent on the chairs and materials ($18 for the fabric and four more for the nail head – we had the rest already).

MCM Chairs Finished From Stairs

I might fix the back of the seat because you can see the puckered fabric.  Not perfect, but not terrible for my first rounded corner cushions.

MCM Chairs Finished Toward Kitchen

How’s that for a Cinderella story?  What do you think?  Have any plans for the upcoming long weekend?

I Chickened Out

This is about those five dollar chairs I snagged at ReStore got a little overhaul.  Great lines and deceptively comfortable, but not in the best condition or colors.

ReStore-Chairs-by-Fireplace-Before

Before I started anything, I took pictures of the upholstery detail.  Because this is my first time upholstering something like this, the pictures could jog my memory if I ran into a problem.

MCM Chairs Upholstery Details Before

With the pictures on my card, I started pulling each staple out.  One at a time, prying with a flat screwdriver then pulling with a pliers.

MCM Chairs Removing Vinyl

Roughly one trillion times.  I counted.  Okay, I didn’t count, but there were a lot. of. staples.

At that point, I wondered what the h–e double hockey sticks I was thinking.  Too late now, I had to keep going.

MCM Chairs Vinyl Tear Off Detail

So I did.  After pulling off the vinyl, I sanded the wood frame down using an orbital hand sander with 220 grit paper.  And loved the lightness against the dark fireplace and the subtle grain.  Two coats of Minwax Polycrylic in a satin finish brings out the grain and protects the wood.  Conveniently, it’s water-based which makes it a breeze to clean up.

MCM Chairs Clear Coat

Then my indecisiveness kicked in.  Upholstery time, but which direction to go.  I stopped in a leather shop, gathered samples and prices, and thought it over.

MCM Chairs Leather Samples

Leather is super durable and easy to clean, but far more expensive than fabric.  Not to mention I could only buy the leather as a full hide, roughly twice as much material as I needed.  Perhaps if I had another use for the leather I could justify buying it.  Instead, I hit up two fabric stores where I found a beige subtle herringbone pattern upholstery fabric for 9 bucks per yard.

I bought it, then stopped in the second store where I found a greige subtle herringbone upholstery remnant for six dollars per yard.  And bought three yards.  Now that I could justify.  Yes, I chickened out on a bold color.  Pillows can fix that.  Right?!

MCM Chairs Fabric to Cut

To get started on the upholstery, I used the vinyl pieces I pulled off as templates, tracing it to the front of my fabric to keep the pattern straight.  Don’t do that!  Add at least 1/2 inch around the sides for a little wiggle room.  I don’t have four hands, so I used a clip to keep my pieces straight while I worked.

MCM Chairs Back Fabric

First tacking the arms, folding the fabric under, wrapping around the back.

MCM Chairs Back Upholstery Arm Back

From the front, it looks like this:

MCM-Chairs-Arm-Detail

With the arms secured, I stapled along the top and bottom, pulling tightly.  Then the sides and finally the slightly rounded corners.

MCM Chairs Back Front Attached

That covers the front of the back rest, so now for the back.  Like the vinyl predecessor, I folded the fabric under, creasing it with my fingers.  Using that crease as a guide for the outer edge, I stapled just inside the crease and worked around the top.

MCM Chairs Adding Back Cover Staples

The corners are tricky to staple under, so then I tacked the bottom of the fabric to the underside.

MCM Chairs Back Cover Panel

Satin nickel nail heads, placed using a needle nose pliers, hold the sides of the fabric in place.

MCM Chairs Nail Head Detail

I’ve upholstered chair seats before, so I thought the back would be more tedious than the seat.  As usual, I under estimated.

MCM Chairs Seat Upholstery

Turns out, the slight curves of the seat were a pain in the arse.  No matter how hard I tried, the fabric puckerd at the turns.  Finally I gave up and let the slight puckers stay.  So, if anyone has pointers, please share!  I’ll leave you with that, because I have to clean up the family room to take pictures of the finished chairs.  Let’s pretend it’s because there are already 17 pictures in this post, okay?

Thank You, Spring Cleaning

I swear I can thank spring cleaning for my most recent thrifty finds.  First a Drexel dresser for the boys’ room and now two chairs and a foot stool.

ReStore-Chairs-by-Fireplace-Before

I found the chairs at Habitat for Humanity ReStore for five bucks each.  Sold!  They’re solid wood and should be easy to refinish and upholster.  Because one has a giant tear in the seat.

ReStore-Chair-Split-Seat

Oh, and the orange vinyl isn’t my fav.

ReStore-Chairs-in-Family-Room-Before

For now, the chairs will live in the family room, replacing the Target slipper chairs, which are in the living room now.  I’ve been looking for arm chairs with a smallish frame.  Ideally I’d stumble upon something like this for a fraction of the price.  But I’m not holding my breath.

Until that magical day happens, these are okay.  You know, with a little lovin’.

ReStore-Chairs-Before

Surprisingly comfortable, the small footprint of the chairs fits nicely in the walk path perimeter room.  A little more depth would be great to feel more lounge-y.  Eventually (when our kids stop wiping grimy hands on everything) we’ll man up and buy adult furniture.

ReStore-Chairs-from-Stairs

How ’bout that footstool/ottoman/side table for $8?  After a quick search, I saw many similar stools for sale, some as high as $300.

ReStore-Chairs-from-Entry

The cane top has damage, but the wood is in good shape.  I’m considering cutting a larger piece of plywood to set on top, making this footstool a round coffee table.

Thrift-Store-Foot-Stool-Cane-Top

What would you do to these pieces?  Sand and stain?  What type and color fabric for the chairs?  We’ve got cream leather in the basement that I think could look nice.  Thoughts?

I’m Bringing Drexel Back

Admittedly not as catchy as bringing sexy back.  On Thursday, the boys and I ran errands, then took advantage of the sunny weather by stopping in a garage sale and two thrift stores.  We left Goodwill with three small planters for $1.50 each.

Thrift-Store-Planters

But we hit the jackpot at our second store, striking gold with this beat up Drexel dresser.

Listed at 90 dollars, I wasn’t going to buy it.  I asked if I could get a discount for the scuffs and burns on it.  The manager took off 25% making it $67.  Not needing another dresser, I couldn’t decide.  Yes, it would look great in the boys’ room.  But they had a white one that worked just fine.  So I asked you, and nearly everyone said, “YES!”  Tipping point, I bought it.  Over the weekend, I sanded it down, getting down to bare wood.

Originally I thought I’d stain it dark (to match their bookshelf), but seeing the pretty grain made me question that decision.  Again, I asked you what to do.  This time, votes were about 75/25, so I went with a clear finish and gold painted hardware.

Drexel-Handle-Parts

Now, Drexel’s back and more handsome than ever.

Drexel-Dresser-front

He’s a far cry from the antique-y white dresser of yore, adding a warm wood tone and sleek lines.

Boys'-Bedroom-One-Year-Later

Drexel-Dresser-with-Beds

Look at those legs!  Slightly tapered, no cankles.

Drexel-Dresser-Handle-Stack

Drexel-Dresser-Side

Perhaps the handles are the furniture equivalent of a gold chain?

Drexel-Dresser-Handle-Detail

A few burns and one stain are still slightly visible on the top because they went too deep to sand out.

Drexel-Dresser-Top

Sixty seven dollars well spent.  Because we already had sand paper, spray paint, and clear coat, $67 is all I spent on this guy.

Drexel-Dresser-in-Boys-Room

Another change in the boys’ room that has me chomping at the bit to give this room some attention.  Like paint covering the walls.  All four.  And a twin bed for Ev, once he’s unhappy sleeping in his crib.